CrystaLac Extreme Protection Polyurethane Interior Top Coat


Size: Mini 1/2 Pint
Sheen: Semi-Gloss
Price:
Sale price$15.50
Stock:
In stock

Description

CrystaLac Extreme Protection Polyurethane is an INTERIOR non-yellowing, environmentally safe top coat that is super hard, super clear and super easy to use. It is scratch, chemical, and water resistant.  Not for use on exterior surfaces.

Brand: CrystaLac

Sheen: Gloss, Semi-gloss, Satin, Matte

Size: 8 oz, Pint, Quart and Gallon

Features:

  • Scratch, Chemical, and Water Resistant.
  • Self- Levels, has Low Odor, Low V.O.C.  and cleans up with water.
  • Added UV stabilizers keep dyes & stains brilliant, help protect from fading.
  • Use anywhere extra protection is needed.
  • Dries crystal clear even over white finishes.
  • Excellent for use as a chalk paint sealer.

Application:

CrystaLac Extreme Protection Polyurethane can be applied by either brushing or spraying (gravity feed or HVLP sprayer).

Prior to top coating, it is  recommended to use CrystaLac Amber Toned Sanding Sealer to enrich the warm natural colors in the wood and minimize grain raising.

It is not necessary to sand between each top coat of CrystaLac Extreme Protection Polyurethane. All CrystaLac top coats will bond to the prior coat. CrystaLac polyurethane can be used over thoroughly dried oil or water-based stains, shellac, lacquer, polyurethane or acrylic.  Extreme Protection is an excellent chalk paint sealer to provide a strong protective finish.

If re-coating over an old finish, scuff sand first and remove any surface contaminants such as dirt, waxes or polishes.

Check the CrystaLac water based stains here.  All products are compatible with each other without issues.

Usually 3 to 5 coats of CrystaLac Extreme Protection Polyurethane are sufficient to produce a beautiful, protective finish. Use more if desired.

Coverage is approximately 400 to 500 sq. ft. per gallon.

Dry time is usually 30 min to 1 hour. Allow 2 to 4 hours before re-coating.

  • Do Not use stearated sandpaper or tack cloths.
  • Do Not freeze.
  • Do Not apply below 60 degrees.
  • Do Not thin or clean with lacquer solvents or mineral spirits.
  • Use soap and water for clean-up.

Warranty: Test to your satisfaction on scrap material before using. The manufacturer, The CrystaLac Company, will only replace defective product. Under no circumstances will the manufacturer or distributors be responsible for the cost of application labor, refinishing expenses, or any costs more than the purchase price of the container.

Caution: Keep out of reach of children! Do not ingest. Avoid contact with skin and eyes. Do not breathe vapors. Use with adequate ventilation. When spraying or sanding, use an OSHA approved mask. V.O.C. is less than 1.4 Lbs. per gallon.

Disposal: Consult your local sanitation department. Do not dump on the ground.

Purchase as part of the Crystalac Tumbler Kit .

About Crystalac:

Derek Becker went to paint school in San Francisco, CA where he learned how to formulate all kinds of coatings. He worked as Head Chemist and Formulator for several companies before Crystalac was born.

The family owned and operated business all started in a barn in Candler, Florida. The barn is where all the magical formulations began. Not only did Derek make paint, he made all the mixing equipment and machinery to make his batches with.

He had a successful business going, supplying paint and finishes to several local companies, when decided in 1989 to move to Mountain City, Tennessee and opened up their family business called Becker Labs. That is where the manufacturing plant for CrystaLac products was built and is still operating.

The company is now run by Dorinda, the youngest daughter of Derek who has been working along side her father for the past 18 years and now carries on the family brand.

CrystaLac Top Coats are made with the highest quality ingredients and everything is Environmentally Safe! Making all Eco Friendly products that are easy to use and extremely durable plus great customer service, has always been top priority for the company.

CrystaLac Waterborne Finishing Products are premium grade acrylic and polyurethane resins using the latest waterborne technology. These finishes can be used in place of nitrocellulose lacquer, polyurethane, or varnishes and can be applied to wood, metal, or ceramic products. They dry rapidly to form a crystal clear, hard, durable finish. CrystaLac finishes are designed to be used right from the can and are perfect for use with high volume low pressure (HVLP) equipment or can also be easily brushed.

Payment & Security

American Express Apple Pay Diners Club Discover Meta Pay Google Pay Mastercard PayPal Shop Pay Venmo Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Estimate shipping

You may also like

Recently viewed